Switch to desktop version  
This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Welcome back to the VXOC FORUM. Sorry for our lack of support over the last year but MYBB is back and so are we. Let's get the forum buzzing again... (March 25, 2022) x



Thread Rating:
  • 2 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tags
door wiring only afl retrofit 5

AFL Retrofit wiring 5-Door ONLY.
#1


AFL Retrofit wiring 5-Door ONLY.

Another VXOC First.


****VERY IMPORTANT GM WILL NO LONGER SUPPORT THIS RETROFIT AND THEY WILL NOT SUPPLY A VCI
CUSTOM PROGRAMMING IS NEEDED ONLY A SELECT FEW PEOPLE CAN DO THIS****

This only covers 5-door J's.

This is not a case of swapping wires around on the headlamp plug, there are 2 reasons for this.
1. The wire gauge is different.
2. only a few wires go to the fuse board the rest go inside the car.

So the first thing you need to do is buy some wire and terminals.

I shall give you a list of wire you can choose what ever colours you want but I'll tell you mine and where I got it from in-case you want to follow this a bit better.

Form ECS
20M White /Red 0.5
20M Brown / White 0.5
20M Grey / Black 0.5
10M Purple / Red 0.5
10M Green / Brown 0.5
10M Green / Purple 0.5
10M White 0.5
10M Blue 0.5
15M Black 0.5

From Polevolt
15M Purple / Yellow 1.5
10M Yellow 1.5
3M Blue / Red 1.5
10M Black / White 1.5
15M Black 1.5

From Auto sparks
12M Blue / Brown 1.0
12M Slate / Blue 1.0

From Simtek
10M White / Blue 0.5

Please note I ordered more wire than was needed in case of any mistakes happened.

Terminals were very hard to track down I got them from mouser in the end but was not cheap.

Automotive Connectors FEMALE 2.8MM TERM 2.0MM INSUL DIA TIN

Automotive Connectors FEMALE 2.8MM TERM 3.0MM INSUL DIA TIN

Automotive Connectors 1.5mm FEMALE TERM 0.5-1 SQmm TIN

I ordered 35 of each

You also need to buy the following as I couldn't track the pins outs or the plugs.

2x 93181753 for the levelling sensors.

1x 13314092 for the AFL module connector x2.

You could use the connectors you have for the headlamp but I'd advise you go to a scrap yard and get some from a J or H or you can them new 88988927
The Terminals for these are listed above from Mouser

While you are at the scrap yard you might as well look in the H (Radio area) for the plug needed K28 X1 or you can buy it new 93187174.
The Terminals for this are here http://uk.rs-online.com/web/p/products/6809027/

I shall list all the parts that need new wiring below, This will have a picture of the connector and then a table underneath with the wires (I will only list the wires needed).

Headlamp connectors



AFL E13L
[TR]
[TD]PIN[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]1.5 Black[/TD]
[TD]1150[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]1.5 Yellow[/TD]
[TD]712[/TD]
[TD]Left Headlamp Low Beam Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]4[/TD]
[TD]1.0 Grey / D-Blue[/TD]
[TD]7538[/TD]
[TD]Left Front DRL Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]5[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]6[/TD]
[TD]1.5 Brown / Yellow[/TD]
[TD]189[/TD]
[TD]Headlamp Levelling Motor Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]7[/TD]
[TD]0.5 D-Green / Brown[/TD]
[TD]7529[/TD]
[TD]Linear Interconnect Network Bus 7 (T4F or T95)[/TD]
[/TR]
[TR]
[TD]8[/TD]
[TD]1.5 Black[/TD]
[TD]1050[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]
[TR]
[TD]9[/TD]
[TD]1.5 Yellow / Grey[/TD]
[TD]57[/TD]
[TD]Left Cornering Lamp Supply Voltage (T95)[/TD]
[/TR]
[TR]
[TD]10[/TD]
[TD]1.5 Black[/TD]
[TD]1150[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]




AFL E13R
[TR]
[TD]PIN[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]1.5 Black[/TD]
[TD]1050[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]1.5 Yellow[/TD]
[TD]312[/TD]
[TD]Right Headlamp Low Beam Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]4[/TD]
[TD]1.0 D-Blue / Brown[/TD]
[TD]7539[/TD]
[TD]Right Front DRL Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]5[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]6[/TD]
[TD]1.5 Brown / Yellow[/TD]
[TD]189[/TD]
[TD]Headlamp Levelling Motor Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]7[/TD]
[TD]0.5 D-Green / Violet[/TD]
[TD]7528[/TD]
[TD]Linear Interconnect Network Bus 6 (T4F or T95)[/TD]
[/TR]
[TR]
[TD]8[/TD]
[TD]1.5 Black[/TD]
[TD]1050[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]
[TR]
[TD]9[/TD]
[TD]1.5 Yellow / White[/TD]
[TD]55[/TD]
[TD]Left Cornering Lamp Supply Voltage (T95)[/TD]
[/TR]
[TR]
[TD]10[/TD]
[TD]1.5 Black[/TD]
[TD]1050[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]



Levelling sensors



B51F
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]0.5 Black / Grey[/TD]
[TD]7526[/TD]
[TD]Front Axle Level Sensor Low Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]0.5 Brown / White[/TD]
[TD]7525[/TD]
[TD]Front Axle Level Sensor Signal (T4F or T95)[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]0.5 White / Red[/TD]
[TD]7524[/TD]
[TD]Front Axle Level Sensor 5 Volt Reference (T4F or T95)[/TD]
[/TR]




B51R
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]0.5 Black / Brown[/TD]
[TD]2185[/TD]
[TD]Automatic Level Control Position Sensor Low Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]0.5 Brown[/TD]
[TD]2184[/TD]
[TD]Automatic Level Control Position Sensor Signal (T4F or T95)[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]0.5 White / Red[/TD]
[TD]2165[/TD]
[TD]Automatic Level Control Position Sensor 5 Volt Reference (T4F or T95)[/TD]
[/TR]


Headlamp Levelling Control



AFL K28X1
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]0.5 Black[/TD]
[TD]1150[/TD]
[TD]Ground (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]0.5 White / Red[/TD]
[TD]2165[/TD]
[TD]Automatic Level Control Position Sensor 5 Volt Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]0.5 Black / Brown[/TD]
[TD]2185[/TD]
[TD]Automatic Level Control Position Sensor Low Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]4[/TD]
[TD]0.5 White[/TD]
[TD]2501[/TD]
[TD]High Speed GMLAN Serial Data (-) (1) (T4F or T95)[/TD]
[/TR]
[TR]
[TD]5[/TD]
[TD]0.5 D-Blue[/TD]
[TD]2500[/TD]
[TD]High Speed GMLAN Serial Data (+) (1) (T4F or T95)[/TD]
[/TR]
[TR]
[TD]6[/TD]
[TD]0.5 Brown[/TD]
[TD]2184[/TD]
[TD]Automatic Level Control Position Sensor Signal (T4F or T95)[/TD]
[/TR]
[TR]
[TD]7[/TD]
[TD]0.5 White / D-Blue[/TD]
[TD]5986[/TD]
[TD]Serial Data Communication Enable (T4F or T95)[/TD]
[/TR]
[TR]
[TD]8[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]9[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]10[/TD]
[TD]0.5 Red / Violet[/TD]
[TD]1242[/TD]
[TD]Battery Positive Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]11[/TD]
[TD]0.5 White / Red[/TD]
[TD]7524[/TD]
[TD]Front Axle Level Sensor 5 Volt Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]12[/TD]
[TD]0.5 Black / Grey[/TD]
[TD]7526[/TD]
[TD]Front Axle Level Sensor Low Reference (T4F or T95)[/TD]
[/TR]
[TR]
[TD]13[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]14[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]15[/TD]
[TD]0.5 Brown / White[/TD]
[TD]7525[/TD]
[TD]Front Axle Level Sensor Signal (T4F or T95)[/TD]
[/TR]
[TR]
[TD]16[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]17[/TD]
[TD]0.5 D-Green / Violet[/TD]
[TD]7528[/TD]
[TD]Linear Interconnect Network Bus 6 (T4F or T95)[/TD]
[/TR]
[TR]
[TD]18[/TD]
[TD]0.5 D-Green / Brown[/TD]
[TD]7529[/TD]
[TD]Linear Interconnect Network Bus 7 (T4F or T95)[/TD]
[/TR]




AFL K28X2
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]1.5 Violet / Yellow[/TD]
[TD]539[/TD]
[TD]Run/Crank Ignition 1 Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]1.5 Violet / Yellow[/TD]
[TD]539[/TD]
[TD]Run/Crank Ignition 1 Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]3[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]4[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[TD]Not Used[/TD]
[/TR]
[TR]
[TD]5[/TD]
[TD]1.5 Yellow / White[/TD]
[TD]58[/TD]
[TD]Right Cornering Lamp Supply Voltage (T95)[/TD]
[/TR]
[TR]
[TD]6[/TD]
[TD]1.5 Yellow / Grey[/TD]
[TD]57[/TD]
[TD]Left Cornering Lamp Supply Voltage (T95)[/TD]
[/TR]



BCM (Body Control Module)



BCM K9X1
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]24[/TD]
[TD]0.5 White[/TD]
[TD]2501[/TD]
[TD]High Speed GMLAN Serial Data (-) (1)[/TD]
[/TR]
[TR]
[TD]25[/TD]
[TD]0.5 D-Blue[/TD]
[TD]2500[/TD]
[TD]High Speed GMLAN Serial Data (+) (1)[/TD]
[/TR]





BCM K9X4
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]1.0 D-Blue / Brown[/TD]
[TD]7539[/TD]
[TD]Right Front DRL Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]1.0 Grey / D-Blue[/TD]
[TD]7538[/TD]
[TD]Left Front DRL Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]23[/TD]
[TD]0.5 White / D-Blue[/TD]
[TD]5986[/TD]
[TD]Serial Data Communication Enable[/TD]
[/TR]





BCM K9X5
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]10[/TD]
[TD]0.35 Brown / Yellow[/TD]
[TD]1970[/TD]
[TD]Headlamp Low Beam Relay Control (T4F or T95)[/TD]
[/TR]



Engine Fuse board



FUSEBOARD X50AX1
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]15[/TD]
[TD]1.5 Brown / Yellow[/TD]
[TD]189[/TD]
[TD]Headlamp Levelling Motor Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]50[/TD]
[TD]1.5 Yellow[/TD]
[TD]312[/TD]
[TD]Right Headlamp Low Beam Supply Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]51[/TD]
[TD]1.5 Yellow[/TD]
[TD]712[/TD]
[TD]Left Headlamp Low Beam Supply Voltage (T4F or T95)[/TD]
[/TR]





Fuseboard X50AX2
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]2.5 Violet / Grey[/TD]
[TD]539[/TD]
[TD]Run/Crank Ignition 1 Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]42[/TD]
[TD]0.35 Brown / Yellow[/TD]
[TD]1970[/TD]
[TD]Headlamp Low Beam Relay Control (T4F or T95)[/TD]
[/TR]
[TR]
[TD]64[/TD]
[TD]1.5 Red / Yellow[/TD]
[TD]3040[/TD]
[TD]Battery Positive Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]68[/TD]
[TD]1.5 Red / Yellow[/TD]
[TD]3040[/TD]
[TD]Battery Positive Voltage (T4F or T95)[/TD]
[/TR]
[TR]
[TD]76[/TD]
[TD]0.5 Red / Violet[/TD]
[TD]1242[/TD]
[TD]Battery Positive Voltage (T4F or T95)[/TD]
[/TR]



My Wiring info to simplify all the above.

My Wiring
[TR]
[TD]Start Point[/TD]
[TD]Function[/TD]
[TD]Wire Size / Colour[/TD]
[TD]Circuit[/TD]
[TD]End Point[/TD]
[TD]My Wire Size / Colour[/TD]
[TD]Note's[/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 2[/TD]
[TD]Automatic Level Control Position Sensor 5 Volt[/TD]
[TD]0.5 White / Red[/TD]
[TD]2165[/TD]
[TD]BR51R - Rear Pin 3[/TD]
[TD]0.5 White / Red[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 6[/TD]
[TD]Automatic Level Control Position Sensor Signal[/TD]
[TD]0.5 Brown[/TD]
[TD]2184[/TD]
[TD]BR51R - Rear Pin 2[/TD]
[TD]0.5 Brown / White[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 3[/TD]
[TD]Automatic Level Control Position Sensor Low Ref[/TD]
[TD]0.5 Black / Brown[/TD]
[TD]2185[/TD]
[TD]BR51R - Rear Pin 1[/TD]
[TD]0.5 Grey / Black[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 11[/TD]
[TD]Front Axle Level Sensor 5 Volt Ref[/TD]
[TD]0.5 White / Red[/TD]
[TD]7524[/TD]
[TD]BR51F - Front Pin 3[/TD]
[TD]AS ABOVE[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 15[/TD]
[TD]Front Axle Level Sensor Signal[/TD]
[TD]0.5 Brown / White[/TD]
[TD]7525[/TD]
[TD]BR51F - Front Pin 2[/TD]
[TD]AS ABOVE[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 12[/TD]
[TD]Front Axle Level Sensor Low Ref[/TD]
[TD]0.5 Black / Grey[/TD]
[TD]7526[/TD]
[TD]BR51F - Front Pin 1[/TD]
[TD]AS ABOVE[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X1 pin 15[/TD]
[TD]Headlamp Levelling Motor Supply Voltage[/TD]
[TD]1.5 Brown / Yellow[/TD]
[TD]189[/TD]
[TD]E13R - Right & E13L - Left Pin 6 on both[/TD]
[TD]1.5 Purple / Yellow[/TD]
[TD]Splits in headlight harness after Fuse Board[/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X1 pin 50[/TD]
[TD]Right Headlamp Low Beam Supply Voltage[/TD]
[TD]1.5 Yellow[/TD]
[TD]312[/TD]
[TD]E13R-Right Pin 3[/TD]
[TD]1.5 Yellow[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X1 pin 51[/TD]
[TD]Left Headlamp Low Beam Supply Voltage[/TD]
[TD]1.5 Yellow[/TD]
[TD]712[/TD]
[TD]E13L-Left Pin 3[/TD]
[TD]1.5 Yellow[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X2 pin 2[/TD]
[TD]Run / Crank Ignition 1 Voltage[/TD]
[TD]2.5 Violet / Grey[/TD]
[TD]539[/TD]
[TD]K28 H.L.C.M x2 Pins 1 & 2[/TD]
[TD]2.5 Red / Yellow[/TD]
[TD]Splits in Harness in car goes to K28 X2 pins 1 & 2[/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X2 pin 76[/TD]
[TD]Battery Positive Voltage[/TD]
[TD]0.5 Red / Violet[/TD]
[TD]1242[/TD]
[TD]K28 H.L.C.M x1 Pin 10[/TD]
[TD]0.5 Purple / Red[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X2 pin 42[/TD]
[TD]Headlamp Low Beam Relay Control[/TD]
[TD]0.35 Brown / Yellow[/TD]
[TD]1970[/TD]
[TD]K9 B.C.M x5 Pin 10[/TD]
[TD]N/A see notes ->[/TD]
[TD]Just swap BCM X5 pin 21 in BCM X5 pin 10[/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X2 pin 64[/TD]
[TD]Battery Positive Voltage[/TD]
[TD]1.5 Red / Yellow[/TD]
[TD]3040[/TD]
[TD]Loops Back To Pin 68[/TD]
[TD]1.5 Blue / Red[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]X50A Fuse Block X2 pin68[/TD]
[TD]Battery Positive Voltage[/TD]
[TD]1.5 Red / Yellow[/TD]
[TD]3040[/TD]
[TD]Loops Back To Pin 64[/TD]
[TD]1.5 Blue / Red[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 18[/TD]
[TD]Linear Interconnect Network Bus 7[/TD]
[TD]0.5 D-Green / Brown[/TD]
[TD]7529[/TD]
[TD]E13L-Left Pin 7[/TD]
[TD]0.5 Green / Brown[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 17[/TD]
[TD]Linear Interconnect Network Bus 6[/TD]
[TD]0.5 D-Green / Violet[/TD]
[TD]7528[/TD]
[TD]E13R-Right Pin 7[/TD]
[TD]0.5 Green / Purple[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X2 pin 5[/TD]
[TD]Right Cornering Lamp Supply Voltage[/TD]
[TD]1.5 Yellow / White[/TD]
[TD]58[/TD]
[TD]E13R-Right Pin 9[/TD]
[TD]1.5 Black / White[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X2 pin 6[/TD]
[TD]Left Cornering Lamp Supply Voltage[/TD]
[TD]1.5 Yellow / Grey[/TD]
[TD]57[/TD]
[TD]E13L-Left Pin 9[/TD]
[TD]1.5 Black / White[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K9 B.C.M x4 pin 1[/TD]
[TD]Right Front DRL Supply Voltage[/TD]
[TD]1.0 D-Blue / Brown[/TD]
[TD]7539[/TD]
[TD]E13R-Right Pin 4[/TD]
[TD]1.0 Blue / Brown[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K9 B.C.M x4 pin 2[/TD]
[TD]Left Front DRL Supply Voltage[/TD]
[TD]1.0 Grey / D-Blue[/TD]
[TD]7538[/TD]
[TD]E13L-Left Pin 4[/TD]
[TD]1.0 Blue / Slate[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K9 B.C.M x4 pin 23[/TD]
[TD]Serial Data Communication Enable[/TD]
[TD]0.5 White / D-Blue[/TD]
[TD]5986[/TD]
[TD]K28 H.L.C.M x1 Pin 7[/TD]
[TD]0.5 White / Blue[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 4[/TD]
[TD]High Speed GMLAN Serial Data (-) (1)[/TD]
[TD]0.5 White[/TD]
[TD]2501[/TD]
[TD]B.C.M x1 Pin 24[/TD]
[TD]0.5 White[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]K28 H.C.C.M X1 pin 5[/TD]
[TD]High Speed GMLAN Serial Data (+) (1)[/TD]
[TD]0.5 D-Blue[/TD]
[TD]2500[/TD]
[TD]B.C.M x1 Pin 25[/TD]
[TD]0.5 Blue[/TD]
[TD][/TD]
[/TR]
[TR]
[TD]G102[/TD]
[TD]Ground[/TD]
[TD]1.5 Black[/TD]
[TD]1050[/TD]
[TD]E13R-Right Pins 1, 8, 10[/TD]
[TD]1.5 Black[/TD]
[TD]Use a ground point in the engine bay by the Headlight[/TD]
[/TR]
[TR]
[TD]G101[/TD]
[TD]Ground[/TD]
[TD]1.5 Black[/TD]
[TD]1150[/TD]
[TD]E13L-Left Pins 1, 8, 10[/TD]
[TD]1.5 Black[/TD]
[TD]Use a ground point in the engine bay by the Headlight[/TD]
[/TR]
[TR]
[TD]G101[/TD]
[TD]Ground[/TD]
[TD]0.5 Black[/TD]
[TD]1150[/TD]
[TD]K28 H.L.C.M Pin 1[/TD]
[TD]0.5 Black[/TD]
[TD]Use a ground point in the engine bay by the Headlight[/TD]
[/TR]



Now I will list all Pins that need to be removed (This is for the Halogen system).

If you haven't already get yourself a nice set of Terminal Release Tools, This is the kit I have after trying a few of the cheaper tools that were too short too small or just too big.
http://www.ebay.co.uk/itm/12pce-Terminal-Release-Tool-Kit-Car-Electrical-Connection-Removal-Install-2073-/130963180581?pt=LH_DefaultDomain_3&hash=item1e7e038c25

Engine Fuse Board



Pin Remove X50AX1
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]11[/TD]
[TD]1.5 White[/TD]
[TD]311[/TD]
[TD]Right Headlamp High Beam Supply Voltage (T4A)[/TD]
[/TR]
[TR]
[TD]15[/TD]
[TD]1.0 Violet / D-Green[/TD]
[TD]439[/TD]
[TD]Run/Crank Ignition 1 Voltage (TR6[/TD]
[/TR]
[TR]
[TD]16[/TD]
[TD]1.0 Violet / D-Green[/TD]
[TD]439[/TD]
[TD]Run/Crank Ignition 1 Voltage (TR6[/TD]
[/TR]
[TR]
[TD]18[/TD]
[TD]1.0 D-Blue / Brown[/TD]
[TD]7539[/TD]
[TD]Right Front DRL Supply Voltage (T3N with T4A)[/TD]
[/TR]
[TR]
[TD]19[/TD]
[TD]1.0 Yellow[/TD]
[TD]312[/TD]
[TD]Right Headlamp Low Beam Supply Voltage[/TD]
[/TR]
[TR]
[TD]47[/TD]
[TD]1.5 White[/TD]
[TD]711[/TD]
[TD]Left Headlamp High Beam Supply Voltage (T4A)[/TD]
[/TR]
[TR]
[TD]52[/TD]
[TD]1.0 Yellow[/TD]
[TD]712[/TD]
[TD]Left Headlamp Low Beam Supply Voltage[/TD]
[/TR]
[TR]
[TD]54[/TD]
[TD]1.0 Grey / D-Blue[/TD]
[TD]7538[/TD]
[TD]Left Front DRL Supply Voltage (T3N with T4A)[/TD]
[/TR]





Pin Remove X50AX2
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]18[/TD]
[TD]0.35 Brown / Violet[/TD]
[TD]1969[/TD]
[TD]Headlamp High Beam Relay Control (T4A)[/TD]
[/TR]
[TR]
[TD]37[/TD]
[TD]0.35 Grey / D-Blue[/TD]
[TD]545[/TD]
[TD]DRL Relay Control (T3N with T4A)[/TD]
[/TR]
[TR]
[TD]64[/TD]
[TD]1.0 Yellow[/TD]
[TD]712[/TD]
[TD]Left Headlamp Low Beam Supply Voltage (T4A)[/TD]
[/TR]
[TR]
[TD]66[/TD]
[TD]1.0 Yellow[/TD]
[TD]312[/TD]
[TD]Right Headlamp Low Beam Supply Voltage (T4A)[/TD]
[/TR]


B.C.M (Body Control Module)



Pin Remove BCM K9X4
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]1[/TD]
[TD]1.0 Yellow[/TD]
[TD]312[/TD]
[TD]Right Headlamp Low Beam Supply Voltage (without T4F or T95)[/TD]
[/TR]
[TR]
[TD]2[/TD]
[TD]1.0 Yellow[/TD]
[TD]712[/TD]
[TD]Left Headlamp Low Beam Supply Voltage (without T4F or T95)[/TD]
[/TR]





Pin Remove BCM K9X5
[TR]
[TD]Pin[/TD]
[TD]Wire[/TD]
[TD]Circuit[/TD]
[TD]Function[/TD]
[/TR]
[TR]
[TD]15[/TD]
[TD]0.35 Grey / D-Blue[/TD]
[TD]545[/TD]
[TD]DRL Relay Control (T3N with T4A)[/TD]
[/TR]
[TR]
[TD]18[/TD]
[TD]0.35 Brown / Violet[/TD]
[TD]1969[/TD]
[TD]Headlamp High Beam Relay Control (T4A)[/TD]
[/TR]
[TR]
[TD]21[/TD]
[TD]0.35 White / Brown[/TD]
[TD]544[/TD]
[TD]DRL Relay Control (T3N with T4A)[/TD]
[/TR]


Once you have made all the wiring changes your new AFL lights will only only work you've you requested a VCI it's not as simple as just request it for the AFL Also AFL is not a recognized retrofit and therefore it's not quite so straight forward.

All this information was gathered by myself and shown to work after successfully obtaining the VCI codes on 27th October 2014.

As with all electrical how-to's
we except no responsibility for any issues
that could arise all are carried out at your own risk.
If the how-to is followed correctly you should have no issues.


PLEASE ASK ALL QUESTION IN THIS THREAD AS PM'S WILL BE IGNORED
(LET OTHERS KNOW THE ANSWER/S TO ANY QUESTION/S TOO)


****VERY IMPORTANT GM WILL NO LONGER SUPPORT THIS RETROFIT AND THEY WILL NOT SUPPLY A VCI****

Astra-J 2.0 CDTI S/S
Retrofitted AFL, TPMS, Navi950, BT, DAB, Rear Camera, Infinity sound system, Towbar, Flexfloor & more.
I can do programming and retrofits using genuine GM MDI and Dealer software.
Reply


Messages In This Thread
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 13:th-Mar-2015, 14:42:17
AFL Retrofit wiring 5-Door ONLY. - by Nemo - 5:th-Jan-2016, 19:04:56
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 5:th-Jan-2016, 20:35:36
AFL Retrofit wiring 5-Door ONLY. - by Nemo - 5:th-Jan-2016, 20:36:01
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 29:th-Jun-2016, 09:10:23
RE: AFL Retrofit wiring 5-Door ONLY. - by z8083 - 23:rd-Jul-2019, 21:05:21
RE: AFL Retrofit wiring 5-Door ONLY. - by z8083 - 30:th-Aug-2019, 21:27:35
RE: AFL Retrofit wiring 5-Door ONLY. - by sergiu26 - 7:th-May-2020, 22:31:03
RE: AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 18:th-May-2020, 14:17:02
RE: AFL Retrofit wiring 5-Door ONLY. - by Peterrl - 31:st-May-2020, 20:38:03
AFL Retrofit wiring 5-Door ONLY. - by cornishtaz - 14:th-Mar-2015, 15:18:31
AFL Retrofit wiring 5-Door ONLY. - by tucpal - 14:th-Mar-2015, 15:23:39
AFL Retrofit wiring 5-Door ONLY. - by bhalay207 - 17:th-Mar-2015, 20:03:15
AFL Retrofit wiring 5-Door ONLY. - by luffy - 27:th-Mar-2015, 19:20:44
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 28:th-Mar-2015, 08:27:13
AFL Retrofit wiring 5-Door ONLY. - by luffy - 28:th-Mar-2015, 08:37:29
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 28:th-Mar-2015, 11:20:18
AFL Retrofit wiring 5-Door ONLY. - by luffy - 28:th-Mar-2015, 11:44:11
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 28:th-Mar-2015, 12:24:15
AFL Retrofit wiring 5-Door ONLY. - by luffy - 28:th-Mar-2015, 12:39:52
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 28:th-Mar-2015, 15:08:59
AFL Retrofit wiring 5-Door ONLY. - by luffy - 28:th-Mar-2015, 16:40:29
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 29:th-Mar-2015, 09:13:38
AFL Retrofit wiring 5-Door ONLY. - by luffy - 29:th-Mar-2015, 10:44:23
AFL Retrofit wiring 5-Door ONLY. - by Lewis6317 - 29:th-Mar-2015, 15:41:44
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 29:th-Mar-2015, 17:16:06
AFL Retrofit wiring 5-Door ONLY. - by luffy - 30:th-Mar-2015, 16:52:15
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 30:th-Mar-2015, 18:11:45
AFL Retrofit wiring 5-Door ONLY. - by luffy - 30:th-Mar-2015, 18:27:11
AFL Retrofit wiring 5-Door ONLY. - by Rusty2009 - 30:th-Mar-2015, 20:31:02

Possibly Related Threads…
Thread Author Replies Views Last Post
  Insignia fog lights retrofit guide zzattack 16 16,637 7:th-Jun-2021, 13:18:53
Last Post: zzattack
  quickheat retrofit WIP Lansa 9 12,783 22:nd-Apr-2021, 21:03:17
Last Post: Lansa
  How To Modify Rear Door Card From Car With Elec Windows To Fit Car With Window Winder Jetcolour 5 5,773 24:th-May-2020, 10:19:26
Last Post: Rusty2009
  Howto Retrofit TPMS Rusty2009 52 41,428 20:th-Feb-2020, 22:06:39
Last Post: komshija
  How to retrofit flex floor Astra-J (MK6) 5 Door Rusty2009 11 25,022 18:th-Feb-2020, 08:13:37
Last Post: Rusty2009
  Retrofit Rear Power point 5 door Astra J Ballinlea 3 11,149 20:th-Mar-2019, 18:13:44
Last Post: Rusty2009
  Single to dual horn upgrade retrofit Lansa 13 14,198 27:th-Jul-2018, 11:20:55
Last Post: Lansa
  Astra gtc retrofit foglights Daniel199025 1 4,549 19:th-Jul-2018, 07:32:40
Last Post: Rusty2009
  Bluetooth retrofit wiring tzr608 9 9,314 18:th-Jul-2018, 19:13:21
Last Post: tzr608
  Retrofit battery cover Rusty2009 35 22,886 3:rd-Dec-2014, 19:02:30
Last Post: Rusty2009

Who read this thread?
9 User(s) read this thread:
Rusty2009 (28:th-Oct-2023, 15:39:26), marktourino (3:rd-Jun-2023, 07:56:34), KKEVANSKK (14:th-May-2023, 17:44:49), milozic (7:th-Sep-2023, 20:59:01), Xeni (6:th-May-2023, 15:12:58), Apotetyk (5:th-May-2023, 22:42:36), M.Duman (28:th-May-2023, 16:40:45), greg848484 (21:st-Mar-2024, 20:22:25), Lito4h (25:th-Nov-2023, 09:38:14)

Forum Jump:


Users browsing this thread: 1 Guest(s)